BOSCH REXROTH
S20-DIDO-8/1
R911173745
I/O IndraControl S20 Digital
BOSCH REXROTH
MATERIAL: R911173745
SUMMARY: I/O IndraControl S20 Digital
Quantity in stock: 1
Quantity Details:- Hydrotech Stock: 0 can ship May 6, 2024
- Factory Stock: 1 can ship June 24, 2024
This module is designed for use within an S20 station. It is used to acquire and output digital signals. The filter times for the inputs can be adjusted to increase the interference immunity. Filter times of 100 μs allow the user to applicatively implement a counting function using an input frequency of maximum 5 kHz. The outputs are protected against short circuits and overload.
General data
Type |
S20-DIDO-8/1 | |
Color |
Gray | |
Weight 1) |
g |
133 |
Ambient temperature (operation) |
-25 °C ... +60 °C | |
Ambient temperature (storage/transport) |
-40 °C ... +85 °C | |
Permissible relative humidity (operation) |
5 % ... 95 %, no dewing | |
Permissible relative humidity (storage/transport) |
5 % ... 95 %, no dewing | |
Air pressure (operation) |
70 kPa ... 106 kPa (up to 3000 m above sea level) | |
Air pressure (storage/transport) |
70 kPa ... 106 kPa (up to 3000 m above sea level) | |
Protection type |
IP20 | |
Protection class |
III, IEC 61140, EN 61140, VDE 0140-1 |
1) | Including plug and bus base module |
Connection data
Type |
S20-DIDO-8/1 | |
Designation |
S20 connector | |
Connection type |
Spring-cage connection with direct plug technology | |
Conductor cross-section solid/flexible/AWG |
0.2 mm² ... 1.5 mm² 0.2 mm² ... 1.5 mm² 24 ... 16 |
|
Stripping length |
mm |
8 |
Interface local bus
Type |
S20-DIDO-8/1 | |
Connection type |
Bus base module | |
Transmission speed |
MBit/s |
100 |
Power supply to logic
Type |
S20-DIDO-8/1 | |
Logic voltage UBus 1) |
V DC |
5 |
Maximum current consumption from UBus |
mA |
120 |
Maximum power consumption from UBus |
mW |
600 |
1) | Via bus base module |
Power supply to peripherals
Type |
S20-DIDO-8/1 | |
Feed to digital input modules UI |
V DC |
24 |
Maximum permitted voltage range 1) |
19.2 V DC ... 30 V DC | |
Current consumption from UI |
mA |
20 |
Typical power consumption from UI |
mW |
380 |
Maximum power consumption from UI |
mW |
480 |
Overvoltage/reverse polarity protection supply voltage |
Electronic (35 V, 0.5 s) / parallel diode; with external security 5 A (only for commissioning) | |
Guarantee 2) |
A |
≤ 8 |
1) | Including all tolerances, including ripple |
2) | Reverse polarity protection up to 5 A |
Digital inputs
Type |
S20-DIDO-8/1 | |
Number of digital inputs |
8 | |
Connection type |
Direct plug-in technology | |
Connectivity technology |
1-wire technology | |
Description of the input |
Acc. to EN 61131-2 type 1 and type 3 | |
Nominal input voltage |
V DC |
24 |
Nominal input current |
mA |
2.4 |
Current profile |
Linear up to nominal current, then constant around 2.4 mA | |
Input voltage range "0" signal |
-3 V DC ... 5 V DC | |
Input voltage range "1" signal |
11 V DC ... 30 V DC | |
Input filter time |
< 100 µs; 1000 µs; 3000 µs (default) | |
Process data update 1) |
µs |
< 100 |
Reverse polarity protection |
Parallel diode (30 V, 5 s) |
1) | Bus synchronous |
Digital outputs
Type |
S20-DIDO-8/1 | |||
Number of digital outputs |
8 | |||
Connection type |
Direct plug-in technology | |||
Connectivity technology |
1-wire technology | |||
Nominal output voltage |
24 V DC | |||
Output current per channel |
mA |
≤ 500 | ||
Output current per device 1) |
A |
≤ 4 | ||
Nominal load |
Ohmic |
48 Ω; for nominal voltage |
W |
≤ 12 |
Lamps |
for nominal voltage |
W |
≤ 12 | |
Inductance |
1.2 H, 48 Ω; for nominal voltage |
VA |
≤ 12 | |
Signal delay upon activation |
µs |
≤ 100 | ||
Signal delay upon deactivation 2) |
µs |
≤ 100 | ||
Switching frequency |
Max. 10000 per second (for minimum 50 mA load current) Max. 1 per second (for inductive nominal load) Max. 16 per second (for lamp nominal load) |
|||
Load |
Ω |
≥ 10 | ||
Limited inductive cut-off voltage |
-25.8 V ... -15 V | |||
Output voltage in deactivated state |
V |
≤ 1 | ||
Output current in deactivated state |
μA |
≤ 300 | ||
Behavior |
For overload |
Shutdown with automatic restart | ||
For inductive overload |
Output can be destroyed | |||
Reverse voltage protection from short pulses |
Limited reverse voltage protection up to 0.5 A for 1 s | |||
Overcurrent cutoff |
A |
> 0.7 | ||
Output current upon overvoltage in deactivated state |
mA |
< 1 | ||
Short-circuit protection, overload protection of the outputs |
Electronic |
1) | Secure externally |
2) | With at least 50 mA load current |
PROFIBUS telegram data
Type |
S20-DIDO-8/1 | |
Need for parameter data |
byte |
3 |
Need for configuration data |
byte |
7 |
Error messages to the higher-level control or computer system
Type |
S20-DIDO-8/1 | |
Error message |
Failure in peripheral supply Short-circuit/overload of digital outputs |
Electrical isolation/insulation of the voltage ranges
Type |
S20-DIDO-8/1 | |
Test distance |
Test voltage | |
5 V supply (logic)/24 V supply (peripherals) |
500 V AC, 50 Hz, 1 min. | |
5 V supply (logic)/function earth |
500 V AC, 50 Hz, 1 min. | |
24 V supply (peripherals)/function earth |
500 V AC, 50 Hz, 1 min. |
Mechanical tests
Type |
S20-DIDO-8/1 | |
Vibration resistance 1) |
g |
5 |
Shock 2) |
30 g, 11 ms duration, semi-sinusoidal shock pulse | |
Continuous shock 2) |
g |
10 |
1) | Acc. to EN 60068-2-6/IEC 60068-2-6 |
2) | Acc. to EN 60068-2-27/IEC 60068-2-27 |
Conformity
Type |
S20-DIDO-8/1 | ||
Conforms with |
|||
Testing of interference immunity acc. to EN 61000-6-2 |
Discharge of static electricity (ESD) |
Criterion B; 6 kV contact discharge; 8 kV air discharge acc. to EN 61000-4-2/IEC 61000-4-2 | |
Electro-magnetic fields |
Criterion A; field strength: 10 V/m acc. to EN 61000-4-3/IEC 61000-4-3 | ||
Fast transients (burst) |
Criterion B; 2 kV acc. to EN 61000-4-4/IEC 61000-4-4 | ||
Transient overvoltage (surge) |
Criterion B; supply lines DC: ±0.5 kV/±0.5 kV (symmetric/asymmetric) acc. to EN 61000-4-5/IEC 61000-4-5 | ||
Line-fed disturbances |
Criterion A; test voltage 10 V acc. to EN 61000-4-6/IEC 61000-4-6 | ||
Testing of disturbance transmission acc. to EN 61000-6-3 |
Radio disturbance characteristics |
Class B acc. to EN 55022 |
Approvals |
The current approvals can be found at www.boschrexroth.com. |
Dimensions
Type |
S20-DIDO-8/1 | |
A |
mm |
35 |
B |
mm |
126.1 |
C |
mm |
54 |
Note on dimensions |
The depth applies when using a support rail TH 35-7.5 (acc. to EN 60715). |