RSDCMQV - Pilot operated, balanced piston sequence valve
Part Number: RSDCMQV
Manufacturer: Sun Hydraulics
Pilot-operated, balanced piston sequence valves will supply a secondary circuit with flow once the pressure at the inlet (port 1) has exceeded the valve setting. The pressure setting of a sequence valve controls the pressure at port 1 relative to the pressure at the drain (port 3). These valves are insensitive to back pressure at port 2 (sequence), up to the valve setting. They may be used to regulate pressure in place of 2-port relief valves if there is pressure in the return line.
- All 3 port sequence cartridges are physically and functionally interchangeable (i.e. same flow path, same cavity for a given frame size).
- Pilot flow continues to increase as the pressure at port 1 (inlet), relative to the pressure at port 3 (drain), rises above the valve setting.
- The main stage orifice is protected by a 150 micron stainless steel screen.
- Pressure at port 3 is directly additive to the valve setting at a 1:1 ratio and should not exceed 5000 psi (350 bar).
- Not suitable for use in load holding applications due to spool leakage.
- W and Y controls (where applicable) can be specified with or without a special setting. When no special setting is specified, the valve is adjustable throughout its full range using the W or Y control. When a special setting is specified, this setting represents the maximum setting of the valve.
- Corrosion resistant cartridge valves are intended for use in corrosive environments and are identified by the model code suffix /AP for external stainless steel components, or /LH for external zinc-nickel plated components. See the CONFIGURATION section for all options. For further details, please see the Materials of Construction page located under TECH RESOURCES.
- Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.
|Capacity||15 gpm60 L/min.|
|Factory Pressure Settings Established at||4 gpm15 L/min.|
|Maximum Operating Pressure||5000 psi350 bar|
|Control Pilot Flow||7 - 10 in³/min.0,11 - 0,16 L/min.|
|Response Time - Typical||10 ms10 ms|
|Maximum Valve Leakage at 110 SUS (24 cSt)||2 in³/min.@1000 psi30 cc/min.@70 bar|
|Adjustment - Number of Clockwise Turns to Increase Setting||55|
|Valve Hex Size||7/8 in.22,2 mm|
|Valve Installation Torque||30 - 35 lbf ft41 - 47 Nm|
|Adjustment Screw Internal Hex Size||5/32 in.4 mm|
|Locknut Hex Size||9/16 in.15 mm|
|Locknut Torque||80 - 90 lbf in.9 - 10 Nm|
|Model Weight||.30 lb0,15 kg|
|Seal kit - Cartridge||Viton: 990-011-006|
|What are the tolerances on pressure settings for Sun's pressure control valves?||Pressure setting tolerances are listed in our Performance Data page. A link to this page can also be found in the Additional Resources tab of the applicable product page.|
|How big is a drop of hydraulic oil?||There are exactly 250 Sun drops in a cubic inch or 15 in a cc.|
|What does Sun mean by the term sequencing?||A sequence valve opens when the pressure at port 1 exceeds the setting of the valve. When pressures at port 1 and port 2 both exceed the setting of the valve the valve goes full open, or sequences. When this happens flow can go in either direction, just so long as port 1 stays above the setting.|
- Sequence Valves Technical Tips
- Sun Offers Zinc-Nickel Plating for Corrosion Resistance
- Sun Cartridges with EPDM Seals
- Sun Expands Corrosion-Resistant Solutions
- QuickDesign with SmartConnect Offers Drag-and-Drop Schematic Tool
- Series 4 PLUS Cartridges Offer Higher Flows with Lower Pressure Losses
- Manufacturing Sun Cartridge Cavities
- Sequence Valves
- Sun's Floating Style Screw-In Cartridge
- Units of Measure, Settings, and Conversions
- Sun Model Code Explanation; 999-901-334
- Cavity Information (S-171) and Tooling
- Cartridges: Materials of Construction
- Fluid and Temperature Recommendations
- Performance Data
- For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.