Hydrotech Acquires Isaacs
Hydrotech ecommerce supports the continental US only

BOSCH REXROTH
Z2FS22-8-3X/S2V
R900468786
Flow Control Throttle Valves

Flow-/throttle valves: Z2FS 22.-3x/

$1,492.00

BOSCH REXROTH

MATERIAL:  R900468786

SUMMARY:  Flow-/throttle valves: Z2FS 22.-3x/

Quantity in stock: 2

Quantity Details:
  • Hydrotech Stock: 0 can ship March 28, 2024
  • Factory Stock: 2 can ship May 9, 2024
Add to Cart

The valve type Z2FS is a throttle check valve in sandwich plate design. It is used for the flow limitation of one or two actuator ports.

Two symmetrically arranged throttle check valves limit flows (by adjustable throttle spools) in one direction and allow free return flow in the opposite direction.

In case of supply throttling, the hydraulic fluid is directed through channel A➀ via throttling point (1) to actuator A➁. The throttle spool (2.1) can be axially adjusted via the spindle (3) for adjustment of the throttling point (1).

Simultaneously, the hydraulic fluid in channel A➀ is directed via the bore (4) to the piston side (5). The active pressure and the spring force retain the throttle spool (2.1) in throttle position.

The hydraulic fluid return flow from actuator B➁ displaces the throttle spool (2.2) and enables the unobstructed flow as check valve. Depending on the version ("S" or "S2"), the throttling effect may occur in supply or discharge.

 

Flow limitation

For actuator velocity adjustment, the throttle check valve is installed between the directional valve and the subplate.

Supply throttling

technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/

component side

plate side

01

02

03

04

05

06

07

08

09

Z2FS

22

8

3X

/

*

01

Throttle check valve, sandwich plate design

Z2FS

02

Size 25

22

03

Throttle check valve side A and B

Throttle check valve side A

A

Throttle check valve side B

B

Adjustment type

04

Spindle with internal hexagon

8

05

Component series 30 ... 39 (30 ... 39: unchanged installation and connection dimensions)

3X

06

Supply throttling

S

Discharge throttling

S2

Corrosion resistance (outside)

07

None (valve housing primed)

no code

Improved corrosion protection (240 h salt spray test according to EN ISO 9227)

J3

Seal material

08

NBR seals

no code

FKM seals

V

Observe compatibility of seals with hydraulic fluid used. (Other seals upon request)

09

Further details in the plain text

*

general

Size

25

Weight (approx.)

kg

8

Installation position

any

Ambient temperature range

NBR seals

°C

-30 … +50

FKM seals

°C

-20 … +50

hydraulic

Size

25

Maximum operating pressure

bar

350

Maximum flow

l/min

360

Hydraulic fluid

see table

Hydraulic fluid temperature range

NBR seals

°C

-30 … +80

FKM seals

°C

-20 … +50

Viscosity range

mm²/s

2.8 … 380

Maximum admissible degree of contamination of the hydraulic fluid, cleanliness class according to ISO 4406 (c) 1)

Class 20/18/15
1) The cleanliness classes specified for the components must be adhered to in hydraulic systems. Effective filtration prevents faults and simultaneously increases the life cycle of the components. For the selection of the filters, see www.boschrexroth.com/filter.

Hydraulic fluid

Classification

Suitable sealing materials

Standards

Data sheet

Mineral oils

HL, HLP, HLPD, HVLP, HVLPD

NBR, FKM

DIN 51524

90220

Bio-degradable

Insoluble in water

HETG 1)

NBR, FKM

ISO 15380

90221

HEES 1)

FKM

Soluble in water

HEPG 1)

FKM

ISO 15380

Flame-resistant

Water-free

HFDU (glycol base)

FKM

ISO 12922

90222

HFDU (ester base)

1)

FKM

HFDR

FKM

Containing water

HFC (Fuchs Hydrotherm 46M, Petrofer Ultra Safe 620) 1)

NBR

ISO 12922

90223

Important information on hydraulic fluids:

For more information and data on the use of other hydraulicfluids, please refer to the data sheets above or contact us. There may be limitations regarding the technical valve data (temperature, pressure range, life cycle, maintenance intervals, etc.). The ignition temperature of the hydraulic fluid used must be 50 K higher than the maximum surface temperature. Flame-resistant - containing water: Maximum pressure differential 210 bar, otherwise, increased cavitation erosion Life cycle as compared to operation with mineral oil HL, HLP 30 … 100%. Maximum hydraulic fluid temperature 60 °C Bio-degradable and flame-resistant – containing water: If this hydraulic fluid is used, small amounts of dissolved zinc may get into the hydraulic system.
1) Not recommended for corrosion-protected version "J3" (contains zinc)

For applications outside these parameters, please consult us!

(measured with HLP46, ϑOil = 40 ±5 °C)

Δp-qV characteristic curves

Via check valve with closed throttle

technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/

Δp-qV characteristic curves

Constant throttle position

technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/

component side

plate side

Supply throttling "S"

Version "-"

technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/

Version "A"

technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/

Version "B"

technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/

Discharge throttling "S2"

Version "-"

technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/

Version "A"

technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/

Version "B"

technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/

Dimensions in mm

technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/
technical illustration-Z2FS22-8-3X/S2V-Flow-/throttle valves: Z2FS 22.-3x/

Required surface quality of the valve contact surface

1

Name plate

2

Adjustment type "8“

Spindle for changing the flow cross-section (internal hexagon SW6)

Left rotation = higher flow Right rotation = lower flow

3

Through holes for valve mounting

4

Same seal rings for ports A, B, P, T

5

Identical seal rings for ports X, Y, L

6

Locking pin (included in the scope of delivery)

7

Hexagon SW22, tightening torque MA = 25 Nm

8

Porting pattern according to  ISO 4401-08-08-0-05

9.1

Plug screw with version "B"

9.2

Plug screw with version "A"

Valve mounting screws (separate order)

Size

Quantity

Hexagon socket head cap screws

Material number

25

6

ISO 4762 - M12 - 10.9-flZn-240h-L

-

Notice:

Length and tightening torque of the valve mounting screws must be calculated according to the components mounted under and over the sandwich plate valve.