Hydrotech Acquires Isaacs
Hydrotech ecommerce supports the continental US only

BOSCH REXROTH
DBA30H2N1X/350
R900702870
Pressure Relief Valves

Pressure valves: DBA* 30.-1x/

$2,103.00

BOSCH REXROTH

MATERIAL:  R900702870

SUMMARY:  Pressure valves: DBA* 30.-1x/

Add to Cart

Pump safety blocks of type DBA are pilot-operated pressure relief valves which are integrated into a block and intended to be mounted directly onto the SAE pressure port of pumps.

They are used for limiting the operating pressure. The pump safety blocks basically consist of a valve block (1), main spool insert (3) and pilot control valve (2) with adjustment type for pressure adjustment. The valve housing has a port P for the hydraulic fluid input and port P1 for the output. In a branch of the through-bore between these two ports there is the main spool insert. When this is open there is a connection to port T (tank line).

Pump safety block type DBA

The pressure applied in the through-bore acts on the main spool (3). At the same time, pressure is applied to the spring-loaded side of the main spool (3) and to the ball (8) in the pilot control valve (2) via the control lines (6) and (7) which are equipped with nozzles (4) and (5). If the pressure in the through-bore exceeds the value set at spring (9), ball (8) opens against spring (9).

The signal for this is provided internally from the through-bore via control lines (10) and (6). The hydraulic fluid on the spring-loaded side of main spool (3) now flows via the control line (7), nozzle bore (11) and ball (8) into the spring chamber (12). From here, it is fed into the tank, either internally for type DBA …– via control line (13), or externally for type DBA …Y via control line (14). Nozzles (4) and (5) cause a pressure drop to occur at the main spool (3), hence the connection from channel P to channel T opens. The hydraulic fluid now flows from channel P to channel T, whilst the set operating pressure is maintained.

Port (15) can be used for remote control purposes. If a pressure load cell or a pressure gauge shut-off valve is to be connected here, then version SO616 – without nozzle (4) – must be ordered. This prevents delays in the pressure build-up or brief pressure drops when the pressure gauge shut-off valve is operated.

Pump safety block type DBAR (with check valve)

The integrated check valve maintains the system pressure when the pump is disconnected and prevents the hydraulic fluid from returning to the pump. If this valve is selected, no separate check valve is needed.

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

17

18

19

20

21

DBA

1X

/

*

01

Pump safety block

DBA

02

Without directional valve

no code

03

Without check valve

no code

With check valve

R 1)

04

Size 32

30

Size 40

40

Connection / SAE flange

2)

06

Standard flange (200 … 350 bar)

F

High-pressure flange (350 bar)

H

Adjustment type for pressure adjustment

07

Rotary knob

1

Sleeve with hexagon and protective cap

2

Lockable rotary knob with scale

3 3)

Rotary knob with scale

7

08

With main spool Ø24 mm

With main spool Ø28 mm

N

09

Component series 10 ... 19 (10 ... 19: unchanged installation and connection dimensions)

1X

Pressure rating

10

Set pressure … 50 bar

50

Set pressure … 100 bar

100

Set pressure … 200 bar

200

Set pressure … 250 bar

250

Set pressure … 315 bar

315

Set pressure … 350 bar (only version “H”)

350

Pilot flow

11

Pilot oil supply and pilot oil return internal (standard)

– 4)

Internal pilot oil supply, external pilot oil return

Y

12

Standard version

no code

Valve for minimum cracking pressure (not suitable for mutual relief!)

U

13

Without switching shock damping

no code

14

Without directional valve

no code

16

Without manual override

no code

Electrical connection

17

Without mating connector, with connector DIN EN 175301-803

K4 5)

Seal material

19

NBR seals

no code

FKM seals

V

(other seals upon request) Attention! Observe compatibility of seals with hydraulic fluid used!

Type-examination procedure

20

Without type-examination procedure

no code

Type-examination tested safety valve according to PED 2014/68/EU

E

21

Further details in the plain text

*

1) Only … 315 bar
2) Please observe the pressure ratings and connection dimensions! (see dimensions).
3) H-key with material no. R900008158 is included in the scope of delivery.
4) Hyphen “–” only required if 12 and 13 = “no code”
5) Mating connectors, separate order.

Preferred types and standard units are contained in the EPS (standard price list).

general

Size

32 40

Weight

kg

8 11.4

Check valve "R"

kg

0.3 0.4

Switching shock damping "S"

kg

0.6

Installation position

any

Ambient temperature range

NBR seals

°C

-30 … +80

FKM seals

°C

-15 … +80

Minimum stability of the housing materials

Housing materials are to be selected so that there is sufficient safety for all imaginable operating conditions (e.g. with regard to pressure resistance, thread stripping strengths and tightening torques).

Hydraulic fluid

Classification

Suitable sealing materials

Standards

Mineral oils and related hydrocarbons

HL, HLP, HLPD

 

 

NBR, FKM

DIN 51524

Bio-degradable

Insoluble in water

HETG

NBR, FKM

VDMA 24568

 

 

HEES

FKM

Soluble in water

HEPG

FKM

VDMA 24568

 

 

Containing water

Water-free

HFDU, HFDR

FKM

 

ISO 12922

 

Containing water

HFC (Fuchs Hydrotherm 46M, Petrofer Ultra Safe 620)

 

NBR

 

ISO 12922

Important information on hydraulic fluids!

For further information and data on the use of other hydraulic fluids, please refer to data sheet 90220 or contact us! There may be limitations regarding the technical valve data (temperature, pressure range, life cycle, maintenance intervals, etc.)!

Flame-resistant – containing water:

Maximum operating pressure 210 bar Maximum hydraulic fluid temperature 60 °C Expected life cycle as compared to HLP hydraulic oil 30 % to 100 %

Technical data for directional seat valves see data sheet 22058, directional spool valves data sheet 23178.

Also see Deviating technical data for type-examination tested safety valves.

hydraulic

Maximum counter pressure

Port Y

bar

0

Port T

bar

10

Maximum flow

See ordering code, safety instructions and characteristic curves "Type-examination tested safety valve"

Hydraulic fluid

Mineral oil (HL, HLP) to DIN 51524

Hydraulic fluid temperature range

NBR seals

°C

-20 … +60

FKM seals

°C

-15 … +60

Viscosity range

mm²/s

12 … 230

hydraulic

Size

32 40

Maximum operating pressure

Port P

bar

350

Port T

bar

315

Cracking pressure

(with DBAR...)

bar

0.5

Maximum counter pressure

Port Y

bar

315

Maximum set pressure

bar

50
100
200
315
350

Minimum set pressure

flow-dependent, see characteristic curves

Maximum flow

DBA, DBAR

l/min

600
350
650
450

Hydraulic fluid

see table

Hydraulic fluid temperature range

NBR seals

°C

-30 … +80

FKM seals

°C

-15 … +80

Viscosity range

mm²/s

10 … 800

Maximum admissible degree of contamination of the hydraulic fluid 1)

Class 20/18/15 according to ISO 4406 (c)
1) The cleanliness classes specified for the components must be adhered to in hydraulic systems. Effective filtration prevents faults and simultaneously increases the life cycle of the components. For the selection of the filters, see www.boschrexroth.com/filter.

For applications outside these parameters, please consult us!

Deviating technical data: Type-examination tested safety valves type DBA…E, component series 1X according to Pressure Equipment Directive 97/23/E C1)

(measured with HLP46, ϑOil = 40 ±5 °C)

Standard version

Minimum set pressure and circulation pressure dependent on the flow

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Notice!

The characteristic curves were measured with external, depressurized pilot oil return.

Due to the internal pilot oil return, the inlet pressure increases by the output pressure present in port T.

The characteristic curves apply to the pressure at the valve output pT = 0 baracross the entire flow range.

Version “U”

Minimum set pressure and circulation pressure dependent on the flow

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Inlet pressure dependent on the flow

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Maximum admissible flow qV max dependent on the counter pressure pT in the discharge line with internal pilot oil return

Type DBA 30 …-1X/…E

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Characteristic curves for intermediate values can be generated by interpolation.

Further explanations see explanation of the diagrams

Type DBA 40 …-1X/…E

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

pA

Response pressure in bar

pT

maximum admissible counter pressure in bar) (sum of all possible counter pressures; also see AD2000 - data sheet A2)

maximum admissible flow in l/min

10 % x pA (with qV = 0) according to PED 97/23/EC

Explanation of the diagram

(Example: type DBA…E, above):

known:

Flow of the system/accumulator that has to be secured qVmax = 320 l/min

Set response pressure of the safety valve pA = 350 bar

unknown:

pTadmissible

Solution:

see arrows in diagram above

pT admissible (320 l/min; 350 bar) = 16.2 bar

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Type DBA …–..

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Type DBA …Y..

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Type DBAR …–..

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Type DBAR …Y..

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

With directional spool valve

Dimensions in mm

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

1

Name plate

2

Omitted with internal pilot oil return

3

Y port for pilot oil return, external

4

Adjustment type "1"

5

Adjustment type "2"

6

Adjustment type "3"

7

Adjustment type "7"

8

Hexagon SW10

9

Switching shock damping sandwich plate, optional

10

Space required to remove the key

11

Space required to remove the mating connector

12

Valve mounting bores

13.1

Directional spool valve NG6

14

Solenoid “a”

15

Optional auxiliary operating device

16

Mating connector without circuitry (separate order)

17

Mating connector with circuitry (separate order)

18

Seal ring

19

Integrated check valve, version "R"

20

Dimension for valve without manual override

21

Dimension for valve with concealed manual override "N9"

22

Dimension for valve with manual override "N"

23

Space required to remove the coil

24

Lock nut SW17, tightening torque MA = 10+5 Nm

With directional seat valve

Dimensions in mm

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

1

Name plate

2

Omitted with internal pilot oil return

3

Y port for pilot oil return, external

4

Adjustment type "1"

5

Adjustment type "2"

6

Adjustment type "3"

7

Adjustment type "7"

8

Hexagon SW10

9

Switching shock damping sandwich plate, optional

10

Space required to remove the key

11

Space required to remove the mating connector

12

Valve mounting bores

 

13.2

Directional seat valve NG6

14

Solenoid “a”

15

Optional auxiliary operating device

16

Mating connector without circuitry (separate order)

17

Mating connector with circuitry (separate order)

18

Seal ring

19

Integrated check valve, version "R"

23

Space required to remove the coil

24

Lock nut SW17, tightening torque MA = 10+5 Nm

Standardflansche, Ausführung „DBA(R)…F“

Version

L1

L2

L3

L4

B1

B2

B3

B4

B5

B6

H1

H2

H3

H4

H5

H6

ØD1

ØD3

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

DBA32...F 121 138 55 38.5 30.2 58.7 65 48.3 - - 105 125 43 85 43 - 11 45
DBA40...F 138 156 54.5 49.5 35.8 69.9 74.5 54.7 - - 118 138 50 98 56 - 13 54
DBAR32...F 121 138 55 38.5 30.2 58.7 65 48.3 60 80 105 125 43 85 43 9 11 40
DBAR40...F 138 156 54.5 49.5 35.8 69.9 74.5 54.7 60 100 118 138 50 98 56 8 13 54

NG

Version

Ports

4 valve mounting screws ISO 4762 - 10.9

1)

Tightening torqueMA in Nm

2)

P and P1

T

Part number

32

„DBA“

SAE 1 1/4“

G1 1/4

M10 x 120

R913000074

52

„DBAR“

M10 x 125

R913000668

40

„DBA“

SAE 1 1/2“

G1 1/2

M12 x 135

R913024229

77

„DBAR“

M12 x 140

R913000312

High-pressure flanges, version “DBA(R)…H“

Version

L1

L2

L3

L4

B1

B2

B3

B4

B5

B6

H1

H2

H3

H4

H5

H6

ØD1

ØD3

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

DBA32...H 121 138 55 38.5 31.8 66.7 65 48.3 - - 105 125 43 85 43 - 15 45
DBA40...H 138 156 54.5 49.5 36.6 79.4 74.5 54.7 - - 118 138 50 98 56 - 17 54
DBAR32...H 121 138 55 38.5 31.8 66.7 65 48.3 60 90 105 125 43 85 43 8 15 40
DBAR40...H 138 156 54.5 49.5 36.6 79.4 74.5 54.7 65 110 118 138 50 98 56 8 17 54

NG

Version

Ports

4 valve mounting screws ISO 4762 - 10.9

1)

Tightening torqueMA in Nm

2)

P and P1

T

Part number

32

„DBA“

SAE 1 1/4“

G1 1/4

M14 x 135

R913024230

113

„DBAR“

M14 x 145

R913024233

40

„DBA“

SAE 1 1/2“

G1 1/2

M16 x 155

R913024234

184

„DBAR“

M16 x 160

R913000354

1)Valve mounting screws (separate order)
4 hexagon socket head cap screws ISO 4762 - 10.9-flZn-240h-L
(with friction coefficient μtotal = 0.09 … 0.14)
Attention!
For reasons of stability, other valve mounting screws must not be used!
2) The tightening torques are guidelines when using screws with the specified friction coefficients and when using a manual torque wrench (tolerance ± 10 %).

Admissible pressures (flange connections according to DIN ISO 6162-2)

Pressure

bar

SAE 1 1/4″ 250
SAE 1 1/2″ 200

Admissible pressures (flange connections according to DIN ISO 6162-2)

Pressure

bar

SAE 1 1/4″ 350
SAE 1 1/2″ 350

Safety instructions: Type-examination tested safety valves type DBA…E, component series 1X according to Pressure Equipment Directive 97/23/EC

Before ordering a type-examination tested safety valve, it must be ensured that at the desired response pressurep, the maximum admissible flowqV max (= numerical value at the position of letter "G" in the component marking) of the safety valve is higher than the maximum possible flow of the system/accumulator to be secured. In this respect, the applicable regulations must be observed! According to PED 97/23/EC, the increase in the system pressure due to the flow must not exceed 10 % of the set response pressure (see component marking).

The maximum admissible flow qV max stated in the component marking must not be exceeded.

Discharge lines of safety valves must end in a risk-free manner. The accumulation of fluids in the discharge lines must not be possible (see AD2000 - data sheet A2).

With version "B", the lowest adjustable pressure (circulation pressure) is set in case of power failure or cable break. With version "A", the pressure limiting function is set in case of power failure or cable break. Hydraulic counter pressures in port T with internal pilot oil return and/or port Y with external pilot oil return add 1:1 to the response pressure of the valve set at the pilot control.

Example:

Pressure adjustment of the valve due to spring pretensioning (item 9 on page 5) in the pilot control valve/adjustment type

pspring = 200 bar

Hydraulic counter pressure in port T with internal pilot oil return

phydraulic = 50 bar

=> response pressure= pspring+ phydraulic = 250 bar

It is imperative to observe the application notes!

In the plant, the response pressure specified in the component marking is set at a flow of 2 l/min. The maximum admissible flow specified in the component marking applies to:

External pilot oil return “Y” without counter pressure in the pilot oil return line, admissible counter pressure in the discharge line (port T) <15 bar

Internal pilot oil return "–“ without counter pressure in the discharge line (port T) With internal pilot oil return, the system pressure increases by the counter pressure in the discharge line (port T) due to the increasing flow (observe AD2000 - data sheet; A2, item 6.3).

To ensure that this increase in system pressure caused by the flow does not exceed the value of 10 % of the set response pressure, the admissible flow has to be reduced dependent on the counter pressure in the discharge line (port T) (see characteristic curves Safety instructions, Type-examination tested safety valves).

By removing a lead seal at the safety valve, the approval according to the PED becomes void Basically, the requirements of the Pressure Equipment Directive and of data sheet AD2000 A2 have to be observed!

Mating connectors for valves with connector “K4”, without circuitry, standard

3P Z4

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Mating connectors for valves with connector “K4”, without circuitry, standard

3P Z4

For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector” Mating connectors for valves with one or two solenoids (individual connection)

Data sheet

Spare parts & repair

Mating connectors for valves with connector “K4”, with indicator light

3P Z5L

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Mating connectors for valves with connector “K4”, with indicator light

3P Z5L

For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector” Mating connectors for valves with one or two solenoids (individual connection)

Data sheet

Spare parts & repair

Mating connectors for valves with connector “K4”, with indicator light and Zener diode suppression circuit

3P Z5L1

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Mating connectors for valves with connector “K4”, with indicator light and Zener diode suppression circuit

3P Z5L1

For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector” Mating connectors for valves with one or two solenoids (individual connection)

Data sheet

Spare parts & repair

Mating connectors for valves with connector “K4”, with rectifier

3P RZ5

technical illustration-DBA30H2N1X/350-Pressure valves: DBA* 30.-1x/

Mating connectors for valves with connector “K4”, with rectifier

3P RZ5

For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector” Mating connectors for valves with one or two solenoids (individual connection)

Data sheet

Spare parts & repair

Ordering code: Type-examination tested safety valves type DBA…E, component series 1X according to Pressure Equipment Directive 97/23/EC

NG

Type designation

Component marking

Maximum flow qVmax in l/min with pilot oil return

Set response overpressurep in bar

external "Y"

internal "–"

32

2 3 4 5 6

DBA 30 ▢▢N1X/▢▢▢E

TÜV.SV.▢–938.22.F.G.p

200

175

30 ... 60

2 3 4 5 6

DBAR 30 ▢▢N1X/▢▢▢E

400

260

61 ... 110

40

2 3 4 5 6

DBA 40 ▢▢N1X/▢▢▢E

TÜV.SV.▢–939.22.F.G.p

350

300

30 ... 60

2 3 4 5 6

DBAR 40 ▢▢N1X/▢▢▢E

450

350

61 ... 110

2

Standard flange

F

High-pressure flange

H

Adjustment type

3

Hand wheel (pressure adjustment sealed, unloading or setting of a lower response pressure possible!)

1

With sealed protective cap (no adjustment/unloading possible)

2

4

Pressure in the designation is to be entered by the customer, pressure adjustment ≥ 30 ... 350 bar and possible in 5 bar steps.

z. B. 150

Pilot oil supply and return

5

Internal

– 1)

Recommendation: Internal pilot oil supply, external pilot oil return (ordering code according to symbols)

Y

6

NBR seals

no code

FKM seals

V

Value entered at the factory

1X

1) Dash “–” only necessary if 12 and 13 = “no code” (see ordering code)